6 Ways on How to Lubricate Door Handles
Door handles are always rubbing against the door frame making squeaking noises. As a result, the handle eventually wears out and becomes hard to open. And don’t get any solution on how to lubricate your door handles? Then, you may be in the right zone. Because here I discussed it briefly.
In short, you need to go through the following steps: removing the handle, cleaning the handle area, pouring in the lubricant, letting it sit, re-attaching the handle, and reinstalling it.
Sometimes it doesn’t matter how small it is. You should take care of your door handles like any other fixture in your home. However, it’s better to gather all your supplies before starting work.
Let’s dive into the main point
How to Lubricate Door Handles? 6 Easy Steps
Step 1 – Remove the Handle
If your door handle has a cover plate, you will need to remove that. So, The first step is to remove the door handle. The door handles are held on with two screws. With the screws removed, the handle should easily pull off. At the same time, you need to learn more about how to open a jammed door lock
Step 2 – Clean the Area
When cleaning the area, you’ll want to start with a clean surface to get the best results. This means removing any dirt, grime, or other debris on the door handle.
If there’s build-up on the handle, you can use a mild cleaning solution and a soft cloth to gently remove it. Once the area is clean, you’re ready to move on to the next step.
Step 3 – Pour in the Lubricant
Lubricating your door handles is a great way to keep them functioning smoothly. To do this, You’ll need a lubricant specifically designed for this purpose. Pour the lubricant into the lid of the container.
Next, use a cloth or paper towel to apply the lubricant to the door handle. Moreover, You may need to use a toothpick or other tool to help you get into tight spaces. Wipe away any excess lubricant with a clean cloth.
Step 4 – Let Sit
The 4th step is to let the lubricant sit on the door handle for a few minutes. It will help ensure that the handle is well-coated. And won’t cause any sticking or squeaking when you use it(which isn’t great news).
You can also use this time to wipe down any other areas of the door that might need some attention, such as the hinges.
Step 5 – Reattach the Handle
When it comes to doing need Reattach The Handle. The first step is needed to make sure that the screws are all in place. Then, use a screwdriver to tighten them until the handle is secure.
On the other hand, If your door has a lot of traffic. It’s a good idea to check the screws are tight as well. After that, you need to install surface bolt on french door
Step 6 – Reinstall
The last step is to reinstall the doorknob and strike the plate. For to do this, First, open up the door(so that you have access to both sides of the door). Next, take out your hammer and tap on each end cap until it slides into place.
Now line up the other end cap with its corresponding slot on the doorframe then tap on it with your hammer or mallet so that it slides into place as well.
Should You Oil Door Handles?
You already felt the Door handles are one of the most important parts of a door. Because they can also be one of the most frustrating, however, If your door handle is sticking or hard to turn, it might be time to oil it.
But before starting this work, you should keep in mind that few things. Like, Oiling a door handle isn’t difficult and will make opening the door much easier.
In the same way before starting work, All you need is some mineral oil & an old rag. If you feel you need the best old rag, then Scott Rags is the best option for you. And Here’s how to do
Put two drops of oil on each side of the pivot point (usually on either side) after that wipe off any excess with the rag.
Doing this will help prevent corrosion from forming which can lead to more problems down the line such as no longer being able to open your doors at all!
You’ll probably want to reapply this every six months if not sooner. So don’t forget this little maintenance job next time your door starts getting stiffer than usual!
How Do You Lubricate a Sticking Door Handle?
Since you were reading here, I guessed you wanted to learn more about this. So, without delay, Let’s know How do you lubricate a sticking door handle?
The first step is to clean the door handle. For to do this, apply a small amount of lubricant to a clean cloth when you notice that it wiped the surface of the handle properly. Then, again, you need to get into all the nooks and crannies, especially if the handle is textured.
After that If you notice that there is any dirt or grime build-up, so you need to use a mild soap and water solution to clean the door handle. Otherwise, this can cause the door handle to stick.
Once the door handle is clean, dry it off completely. Next, apply a lubricant such as WD-40 or vaseline to the door handle. If you have a sticking keyhole, you can also lubricate this with WD-40 or vaseline.
Finally, test the door handle to see if it is still sticking. If it is, you need to change the door handle as soon as possible.
Still sticking? Disconnect the faceplates on the knobs and slide them off the doors. Remove the latch plate and latch. All that’s left is to oil everything, then reassemble the lockset.
Last Words
Hopefully, you might get an idea of How to lubricate door handles. Doing this certainly doesn’t hurt; in theory, it would lubricate the mechanism more thoroughly.
But in practice, I didn’t notice any difference in operation between the knobs I fixed the easy way and the ones I fixed the harder way.
Last suggestion, If you have any leftover lubricant, you can apply it to other door hardware like hinges or locks. And that’s it!
