How to Install Ball Bearing Drawer Slides? 5 Easy Steps

The bottom ball-bearing drawer slider is a great way to improve the efficiency of your drawer operation. This type of slider is made of high-quality materials and designed to last. So the question is, How to Install Ball Bearing Drawer Slides?

Replacing your old 1-1/4″ or 1-3/4″ ball bearing drawer slides with new ones is a great way to modernize your kitchen. The installation process is simple, requiring only a Phillips screwdriver and no additional tools.

Before you start, read the installation instructions to ensure you understand what is needed.

Installing a new bottom ball-bearing drawer slide can be tricky if you don’t understand the mechanics. We are here to guide you and tell you the procedure.

Contents show

How Do You Install Bottom Ball Bearing Drawer Slides?

You can follow these easy steps to install bottom ball-bearing drawer slides:

Attach the drawer-mount component first. Attach the slide with a screw at the front in a vertical slot and one at the back, with the slides aligned flush to the drawer front and bottom edge.
After separating the slides’ cabinet-mount sections, repeat the same for the other side of the drawer. Sometimes dresser drawers slide out. It has to be fixed.
To ensure the proper offset, seat the wrapped shoulder of the front mounting bracket tightly against the rear of the face frame with the cabinet-mount member in place.
To align the slide up or down, tape a torpedo or other short level, or use one with a magnet that will grab the slides.
Attach the rear mounting bracket. Also, install bottom mount drawer slides.

Product Recommendation:
You can choose Liberty D80616C-ZP-W 16-Inch Ball Bearing Drawer Slides. This is one of the best ball-bearing drawer slides on the market.

Learn More: How to Install Bottom Mount Drawer Slides? 4 Easy Steps

How Do You Put the Drawers Back on a Ball Bearing Track?

Putting drawers back on a ball-bearing track is a relatively simple process. First, use a Phillips head screwdriver to remove the screws that hold the drawer fronts. Next, remove the drawer fronts from the cabinet.

It's pretty easy to reposition drawers on ball-bearing tracks.

Be sure to save the screws that hold the fronts on. Finally, use the screws that you saved to attach the drawer fronts to the cabinet.

Suppose you are installing a sliding drawer in the kitchen cabinet. But you are stuck on how to do it. You can go through our guide, “How to Install Sliding Drawer in Kitchen Cabinets?”

How do I remove ball-bearing drawer slides?

The outcome depends on whether you genuinely only want to take out the sliding drawer or whether you also want to install new slides.

When you notice a release tab, pull the drawer out until you can see it. Push the release tab, and pull the drawer out to replace the slides.
The sliders are then unscrewed and replaced. When the drawer doesn’t close correctly, you then modify them.
It is much simpler to find the loose screw, piece of debris, bent region, or other issues with the current one and fix it.
They have the smallest amount of clearance. Hence, the most frequent problem is a loose screw. If that’s what you discover, remove and relocate or discard it.

This following video shows how to fix drawer slides:

Frequently Asked Question

What are the types of drawer slides?

There are a few different types of drawer slides. The most common type is the rolling type. This slide moves along the drawer track and can be adjusted to different positions. The other type of slide is the gliding type. This type of slide moves along a rail and doesn’t have any adjustment capabilities.

How do ball-bearing drawer slides work?

Ball bearings are held in place by indentations in the edges of two U-shaped channels that move within one another. The top and bottom are where you’ll find them. These enable the channels to proceed with a minimum of resistance.

In a free-floating channel, there may occasionally be three sections with bearings between the outer and inner tracks. The middle track cantilevers over the peripheral channels, allowing the drawer to open entirely.

Final Words

Now you know “How to Install Ball Bearing Drawer Slides?” The installed drawer slides were easy to fit and were much more aesthetically appealing than the cheap plastic rollers. The drawers now glide silently and effortlessly.

The ball-bearing slides are easy to install and require little attention. They are made of steel. The drawer slides are adjustable and made of cast iron. The drawer slides are easy to use and require little time to install.